Iec 61215 download

Vertex Inverter Matching. Trinasmart Whitepaper. Duomax Twin - Bifacial. Trina Module — Fuse Current Rating.

Five Requirements for Residential Rooftop Solar. TrinaPro Solution Guide Book. Antelope Valley Union. Colorado State University. Meridian Center Business Park. Camila Utility Project. Hawk Pointe Golf Club. Oro Loma Sanitary District. Clark County School District. Marriott Towne Places. Oshman Family JCC. Park Villas Rooftop.

The useful service life of modules so qualified will depend on their design, their environment and the conditions under which they are operated. Test results are not construed as a quantitative prediction of module lifetime. This document is intended to apply to all terrestrial flat plate module materials such as crystalline silicon module types as well as thin-film modules. It does not apply to systems that are not long-term applications, such as flexible modules installed in awnings or tenting.

This edition includes the following significant technical changes with respect to the previous edition: a. Addition of test methods required for flexible modules.

This includes the addition of the bending test MQT The recommended stand off height is 6 in. The mounting structure and hardware must be made of durable, corrosion, and UV-resistant material. Electrical Installation Grounding All module frames must be properly grounded.

Grounding is achieved through securement to the array frame. The array frame shall be grounded in accordance with NEC Article Also observe all local electric codes and regulations. A bonding or toothed washer is required to make proper and reliable electrical grounding connection with the anodized aluminum frame.

Devices listed and identified for grounding metallic frames of PV modules are permitted to ground the exposed metallic frames on the module to grounded mounting structure. Per NEC When using lay-in lugs, the grounding conductor should be inserted into the opening indicated in the figure, and secured using the set screw. General electrical installation Do not use modules of different configurations in the same system.

This module is supplied with Multi Contact connectors for electrical connections. Refer to Section Wiring should have a cross section area of 4 mm 2 minimum and must be temperature rated at 90C minimum.

Completely cover system module with an opaque material to prevent electricity from Page 31 of 37 IEC Ed. For best performance, ensure that positive and negative DC wires run closely together avoiding loops. Do not touch bare conductors or other potentially energized parts. Maintenance STPL recommends the following maintenance items to insure optimum performance of the module: Clean the glass surface of the module a s necessary.

Use water and a soft sponge or cloth for cleaning. A mild, non-abrasive cleaning agent can be used if necessary. Do not use dishwasher detergent.

Electrical and mechanical connection should be checked periodically by qualified personnel to verify that they are clean, secure and undamaged. Problems should only be investigated by qualified personnel.

Observe the maintenance inspections for all other components used in the system. Shutting down the system Completely cover system module with an opaque material to prevent electricity from being generated while disconnecting conductors.

Disconnect system from all other power sources in accordance with instructions for all other components used in the system. The system should now be out of operation and can be dismantled. In doing so, observe the all safety instructions as applicable to installation. Electrical rating of the concerned modules: The electrical ratings are provided with trailing sheet of user manual. The information in this manual is based on our knowledge and experience and is believed to be reliable, but such information including product specification without limitations and suggestions does not constitute a warranty, expressed or implied.

SVL reserves the right to change the manual, the product, the specifications, or product information sheets without prior notice.

If you have any further questions well gladly assist you. Note: This manual can be subject to technical modifications without notice Page 32 of 37 IEC Mounting : Mounting - The following mounting hardware is in combination with the following series. The applied torque is 8 Nm. The applicant provided all of the test samples for testing by UL. UL did not select the samples or determine whether the samples provided were representative of other products manufactured by applicant.

UL has not established Follow-Up Service or other surveillance of the product. The applicant is solely responsible for continued compliance of products to all applicable standards..

Open navigation menu. Close suggestions Search Search. User Settings. Skip carousel. Carousel Previous. Carousel Next. What is Scribd? Explore Ebooks. Bestsellers Editors' Picks All Ebooks. Explore Audiobooks. Bestsellers Editors' Picks All audiobooks. Explore Magazines. Editors' Picks All magazines. Explore Podcasts All podcasts.